Amphenol NETBridge To TE MATEnet Single Port Ethernet Adapter Cable

Amphenol NETBridge Plus single port connector on one end, TE MATEnet single port Z coded connector on the other end, factory terminated on original LEONI Dacar 647-4 fully shielded gigabit automotive Ethernet cable. The NETBridge Plus end is offered as female NTHCF011A10S or male NTHCM011A10S, black housing with red latch. The MATEnet end is offered as female 2302510-9 or male 2302461-9, water blue. Four gender combinations cover every possible NETBridge Plus to MATEnet connection. Available in 6 lengths from 0.1 m to 5 m. Built for zonal architectures that must bridge a NETBridge Plus port to a MATEnet device.

Modern zonal vehicles mix connector systems across the architecture. An ECU may use Amphenol NETBridge Plus on one port, while sensors and other ECUs use TE MATEnet. Directly mating NETBridge Plus to MATEnet is impossible because the two connector systems have different shapes, so a factory made adapter cable is required.This cable bridges the two systems. One end is the Amphenol NETBridge Plus single port, black housing with red latch. The other end is the TE MATEnet single port Z coded, water blue. The cable is original LEONI Dacar 647-4, a fully shielded gigabit line built to hold 100 ohm differential impedance end to end.

Whether your ECU uses NETBridge Plus and your sensor uses MATEnet, or your ECU uses MATEnet and your sensor uses NETBridge Plus, this adapter cable crosses the two systems. Four gender combinations cover every possible connection. Pick the configuration that matches the connectors on both ends.

Product Specifications

Available Configurations

NETBridge Plus Female to MATEnet Male

One end is the Amphenol NETBridge Plus single port female, NTHCF011A10S, black housing with red latch, and the other end is the TE MATEnet single port male, 2302461-9, water blue.

Use it when the NETBridge Plus side has a male pigtail and the MATEnet side has a female socket. The NETBridge Plus female plugs into the NETBridge Plus male, and the MATEnet male plugs directly into the MATEnet female socket. The 0.1 m to 5 m range covers dashboard to sensor routing.

NETBridge Plus Female to MATEnet Female

One end is the Amphenol NETBridge Plus single port female, NTHCF011A10S, black housing with red latch, and the other end is the TE MATEnet single port female, 2302510-9, water blue.

Use it when both sides of the link have male pigtails. The NETBridge Plus female plugs into the NETBridge Plus male, and the MATEnet female plugs into the MATEnet male. This is the female to female crossover. The 0.1 m to 5 m range covers dashboard to sensor routing.

NETBridge Plus Male to MATEnet Female

One end is the Amphenol NETBridge Plus single port male, NTHCM011A10S, black housing, and the other end is the TE MATEnet single port female, 2302510-9, water blue.

Use it when the NETBridge Plus side has a female socket and the MATEnet side has a male pigtail. The NETBridge Plus male plugs directly into the NETBridge Plus female, and the MATEnet female accepts the MATEnet male. The 0.1 m to 5 m range covers dashboard to sensor routing.

NETBridge Plus Male to MATEnet Male

One end is the Amphenol NETBridge Plus single port male, NTHCM011A10S, black housing, and the other end is the TE MATEnet single port male, 2302461-9, water blue.

Use it when both sides of the link have female sockets. The NETBridge Plus male plugs into the NETBridge Plus female, and the MATEnet male plugs into the MATEnet female. This is the male to male crossover. The 0.1 m to 5 m range covers dashboard to sensor routing.

Applications 

Closing line: because both ends are factory terminated connectors on the same shielded Dacar 647-4 cable, the gigabit link stays impedance matched end to end.

Professional Services

Connector customization: other NETBridge Plus and MATEnet variants quoted on request.

Fast sampling: small batch samples in days, production volumes on a confirmed lead time.

Length customization: 0.1 m to 5 m in stock. Non standard cut lengths built to your drawing.

Quality before dispatch: 100 percent continuity and shielding continuity tested on every assembly before dispatch.

Configuration customization: 4 gender combinations as shown. Other NETBridge Plus and MATEnet variants quoted on request.

OEM and bulk support: ADAS integrators, zonal ECU developers and R and D labs get volume pricing and private label packaging.

Product FAQ

Q1: What is NETBridge Plus?

NETBridge Plus is an Amphenol automotive Ethernet connector system. This cable uses the NETBridge Plus single port, black housing with red latch, on one end.

Q2: Which length should I order?

0.1 m to 0.5 m for bench or tight ECU jumps, 1 m to 2 m for dashboard routing, 3 m to 5 m for trunk or across cabin runs. When in doubt, take the next length up.

Q3: How do I know which gender to pick?

Look at the connector on each end of your existing harness. If it has pins sticking out, it is male and you need a female end. If it has sockets, it is female and you need a male end. When in doubt, send us photos of both connectors.

Q4: What is the difference between the four configurations?

Config 1 is NETBridge Plus female to MATEnet male. Config 2 is NETBridge Plus female to MATEnet female. Config 3 is NETBridge Plus male to MATEnet female. Config 4 is NETBridge Plus male to MATEnet male. Pick the gender combination that matches the connectors on both ends.