Rosenberger H-MTD Dual Port To Single Port Ethernet Cable

Rosenberger H-MTD dual port female connector, part number E6K10B-1CAZ5-Z, lake blue housing with pink service aid, factory fanned out to two separate H-MTD single port female connectors on GG2SPEED 251 fully shielded 10G automotive Ethernet cable. The dual port carries two independent 10G Ethernet channels in one housing, and the fan out splits them into two individual single port ends. Available in 8 lengths from 0.5 m to 6 m. Built for zonal architectures that need to break a H-MTD dual port out to two separate single port devices.

H-MTD is Rosenberger s 10G automotive Ethernet connector system. The dual port female E6K10B-1CAZ5-Z carries two independent 10G channels in one lake blue housing. When a zonal ECU or gateway uses a H-MTD dual port male pigtail, the two channels often need to reach two separate devices in different locations. A factory fan out cable splits the dual port into two single port ends.This cable covers that exact case. One end is the H-MTD dual port female, E6K10B-1CAZ5-Z. The other end is two separate H-MTD single port females, each with its own pink service aid. The cable is GG2SPEED 251, a fully shielded 10G automotive Ethernet line.

Whether you are fanning out from a H-MTD dual port gateway to two cameras, bridging a dual port ECU to two radar sensors, or building a bench test rig, this fan out cable splits the dual port into two single port runs. Pick the length that matches your routing.

Product Specifications

Available Configurations

H-MTD Dual Port Female to 2x Single Port Female

This fan out cable joins a Rosenberger H-MTD dual port female connector, part number E6K10B-1CAZ5-Z, to two separate H-MTD single port female connectors, on GG2SPEED 251 fully shielded 10G automotive Ethernet cable.

The pink tab on each connector helps identify the H-MTD interface during installation and confirms a fully seated latch when mated. The Z coding means each port mates only with the matching Z coded male, preventing wrong key mating. The dual port housing holds both channels aligned side by side, while the fan out splits them into two individual cable runs that can route to different devices.

H-MTD Dual Port Female to 2x Single Port Female

Inside each connector, the contact is shielded and grounded through a 360 degree termination to the cable braid. The GG2SPEED 251 cable behind each contact is a fully shielded twisted pair rated for 10GBASE T1 operation, built to hold 100 ohm differential impedance across the full cable length. 

Available in 8 lengths from 0.5 m to 6 m. The 0.5 m to 1 m options fit tight ECU jumps inside the dashboard. The 1.5 m to 3 m options cover door to pillar routing and dashboard to camera runs. The 4 m to 6 m options reach from the trunk gateway to roof mounted sensors or across the full cabin. 

Applications 

Closing line: because both channels run through factory terminated H-MTD connectors on the same shielded GG2SPEED 251 cable, both 10G links stay impedance matched end to end.

Professional Services

Fast sampling: small batch samples in days, production volumes on a confirmed lead time.

Length customization: 0.5 m to 6 m in stock. Non standard cut lengths built to your drawing.

Connector customization: other H-MTD dual port and single port combinations quoted on request.

Quality before dispatch: 100 percent per channel continuity and shielding continuity tested on every assembly before dispatch.

OEM and bulk support: ADAS integrators, zonal ECU developers and commercial vehicle makers get volume pricing and private label packaging.

Product FAQ

Q1: Is this a genuine Rosenberger H-MTD connector?

Yes. The H-MTD dual port female is genuine Rosenberger, part number E6K10B-1CAZ5-Z, lake blue with pink service aid. The cable is GG2SPEED 251 fully shielded 10G automotive Ethernet.

Q2: What does the dual port to single port fan out mean?

One end is a combined dual port housing that plugs into a dual port male pigtail. The other end splits into two separate single port connectors, each carrying one 10G channel to a different device.

Q3: Can you make custom lengths or connector combinations?

Yes. We support custom lengths from 0.5 m to 6 m and beyond, and can quote other H-MTD dual port and single port combinations on request. Send us your drawing and target length, and we will quote the matching cable.

Q4: Which length should I order?

0.5 m to 1 m for tight ECU jumps, 2 m to 3 m for dashboard routing, 4 m to 6 m for trunk or across cabin runs. When in doubt, take the next length up.