TE MATEnet 3 Port To LEONI Dacar Automotive Cable

Zonal vehicle architectures push three gigabit Ethernet channels out of one MATEnet 3 port connector. The A coded version uses a black housing that locks into a specific ECU or panel port, keyed so it cannot mate to a Z coded receptacle by mistake. Running three separate cables out of a 3 port housing requires a factory made fan out harness, because hand built splitters fail the 100 ohm impedance and 360 degree shielding tests.

This harness is that factory fan out. The 3 port A coded female, 2324319-1, mates to the factory MATEnet 3 port A coded male pigtail. The cable fans out to three single port connectors, either MATEnet or H-MTD, female or male depending on configuration. The cable is original LEONI Dacar 647-4, a gigabit shielded line built to hold 100 ohm differential impedance on all three channels, backwards compatible with 100 Mbps links.

Genuine TE MATEnet 3 port A coded female connector, part number 2324319-1, black housing, factory fanned out to three single port connectors on original LEONI Dacar 647-4 fully shielded gigabit automotive Ethernet cable. The 3 port A coded female end carries three independent gigabit Ethernet channels. The three fan out ends are offered as MATEnet single port female, MATEnet single port male, MATEnet 3 port A coded female on both ends, H-MTD single port female or H-MTD single port male. Available in 7 lengths from 0.5 m to 5 m. Built for zonal architectures that must break one MATEnet 3 port connector out to three MATEnet or H-MTD devices.

Whether you are breaking a MATEnet 3 port A coded port out to three MATEnet sensors, adapting to three H-MTD devices, or extending a 3 port A coded to 3 port A coded link, this harness has the fan out you need. Pick the configuration that matches the connectors on the other end.

Product Specifications

Available Configurations

3 Port A Coded to 3x MATEnet Single Port Z Coded

The 3 port A coded female end plugs into a MATEnet 3 port A coded male pigtail, and the cable fans out to three MATEnet single port Z coded female receptacles, part number 2302510-9, water blue.

Use it when the three gigabit channels need to reach three separate MATEnet single port female devices, such as three cameras or three radar sensors. Each single port female accepts a standard MATEnet male pigtail. The 0.5 m to 5 m length range covers dashboard to sensor and trunk routing.

3 Port A Coded to 3x MATEnet Single Port Z Coded

The 3 port A coded female end plugs into a MATEnet 3 port A coded male pigtail, and the cable fans out to three MATEnet single port Z coded male plugs, part number 2302461-9, water blue.

Use it when the three devices on the other end have MATEnet female sockets, such as three female ended cameras or test jigs. Each single port male plugs directly into a female socket without an adapter. The 0.5 m to 5 m lengths cover sensor to ECU and bench test routing.

3 Port A Coded Female to 3 Port A Coded Female

Both ends are the MATEnet 3 port A coded female, part number 2324319-1, black housing.

Use it as a 3 port to 3 port extension when a factory MATEnet 3 port A coded male pigtail is too short, or when bridging two 3 port A coded male panel receptacles. The female to female gender keeps both factory pigtails unchanged, and the Dacar 647-4 shielded cable keeps all three gigabit channels clean. The 0.5 m to 5 m range covers tight ECU jumps to full trunk runs.

3 Port A Coded to 3x H-MTD Single Port Z Coded

The MATEnet 3 port A coded female end plugs into the factory MATEnet 3 port A coded pigtail, and the cable fans out to three Rosenberger H-MTD single port Z coded female receptacles, part number E6K10A-1BZZ5-Z, water blue.

Use it when the ECU side uses MATEnet A coded but the three devices use H-MTD. Each H-MTD female accepts a standard H-MTD male sensor pigtail. This is the MATEnet to H-MTD crossover, and the 0.5 m to 5 m range covers everything from a tight dashboard jump to a trunk to cabin run.

3 Port A Coded to 3x H-MTD Single Port Z Coded

The MATEnet 3 port A coded female end plugs into the factory MATEnet 3 port A coded pigtail, and the cable fans out to three Rosenberger H-MTD single port Z coded male plugs, part number E6S10A-1BZZ5-Z, water blue.

Use it when the three devices on the H-MTD side have female sockets, such as three female ended H-MTD cameras or test instruments. Each H-MTD male plugs directly into the female socket. The 0.5 m to 5 m lengths cover sensor to ECU and bench test routing.

Applications 

Closing line: because all three channels run through factory terminated MATEnet or H-MTD connectors on the same shielded Dacar 647-4 cable, the gigabit links stay impedance matched end to end.

Professional Services

Connector customization: other MATEnet and H-MTD variants quoted on request.

Fast sampling: small batch samples in days, production volumes on a confirmed lead time.

Length customization: 0.5 m to 5 m in stock. Non standard cut lengths built to your drawing.

Quality before dispatch: 100 percent per channel continuity and shielding continuity tested on every assembly before dispatch.

OEM and bulk support: zonal ECU developers, ADAS integrators and R and D labs get volume pricing and private label packaging.

Configuration customization: 5 fan out options as shown. Other MATEnet and H-MTD gender and coding combinations quoted on request.

Product FAQ

Q1: Can you make custom lengths or fan out combinations?

Yes. We support custom lengths from 0.5 m to 5 m and beyond, and can mix MATEnet and H-MTD gender and coding combinations on request. Send us your connector photos and target length, and we will quote the matching assembly.

Q2: What is the difference between this 3 port version and the 6 port version?

The 3 port version carries three gigabit channels from a 3 port housing, part number 2324319-1. The 6 port version carries six channels from a 6 port housing, part number 2333538-1. Pick the port count that matches the number of channels on your ECU.

Q3: Is this a genuine TE MATEnet connector?

Yes. The 3 port A coded female housing is genuine TE MATEnet, part number 2324319-1, black housing. The cable is original LEONI Dacar 647-4 fully shielded gigabit automotive Ethernet. The fan out ends are genuine TE MATEnet or Rosenberger H-MTD connectors as listed.

Q4: What is the difference between the five configurations?

Config 1 fans out to three MATEnet single port females. Config 2 fans out to three MATEnet single port males. Config 3 is 3 port A coded female to 3 port A coded female for extension. Config 4 fans out to three H-MTD single port females. Config 5 fans out to three H-MTD single port males.