Product Specifications
| Item | Specification |
| Compliance | RoHS |
| Flame Rating | Flame retardant |
| Conductor | Oxygen free copper |
| Cable Type | Twisted pair, fully shielded |
| Use Environment | In vehicle electronic equipment |
| Brand | TE Connectivity, MATEnet series |
| Config 4 | Panel mount A coded male to bare cut wires |
| Data Rate | 1 Gbps gigabit, backwards compatible with 100 Mbps |
| Cable | LEONI Dacar 647-4, gigabit shielded automotive Ethernet |
| Product Type | MATEnet panel mount gigabit Ethernet extension and adapter harness |
| Length Options | 0.2 m, 0.5 m, 1 m, 1.5 m, 2 m, 2.5 m, 3 m, 4 m, 5 m, custom on request |
| Config 1 | Panel mount A coded male to MATEnet single port female, 2302510-1, black |
| Main Connector | MATEnet single port A coded male, panel mount stud, 2394145-1, black housing |
| Config 3 | Panel mount A coded male to bare female contact pins, no housing on the other end |
| Config 2 | Panel mount A coded male to panel mount A coded male, 2394145-1 both ends, black |
| Config 5 | Bare male contact pins to bare male contact pins, 2302451-1, no housing on either end |
Available Configurations
Panel Mount A Coded to MATEnet Single Port
The panel mount male end clips into a square hole on a panel or bracket, and the other end is a MATEnet single port female receptacle, part number 2302510-1, black housing.
Use it when you need to mount the male connector through a panel and reach a female socket on the device side. The stud holds the connector fixed to the panel, and the female end accepts a standard MATEnet male pigtail. The 0.2 m to 5 m length range covers everything from a tight panel to sensor jump to a trunk run.
Panel Mount A Coded to Panel Mount A Coded
Both ends are the MATEnet panel mount A coded male, part number 2394145-1, black housing with mounting stud.
Use it when you need to mount two male connectors through two panels, or when bridging two female receptacles that are each behind a panel. The stud on each end keeps both connectors fixed in place. The 0.2 m to 5 m range covers panel to panel and across cabin routing.
Panel Mount A Coded to Bare Female Contact Pins
The panel mount male end clips into a panel, and the other end is left as bare female contact pins with no plastic housing, showing the metal terminals only.
Use it when you need to build your own housing on the other end, such as inserting the female pins into a custom panel receptacle or a non standard MATEnet connector.
The panel mount male end gives you a certified MATEnet interface, and the loose pins let you define the other end. The 0.2 m to 5 m range covers custom harness builds and bench test rigs.
Panel Mount A Coded Male to Bare Cut Wires
The panel mount male end clips into a panel, and the other end is left as bare cut wires with the green and white pairs exposed.Use it when you need to terminate the other end yourself, such as soldering to a test board, mating to a non MATEnet connector, or building a custom harness.
The panel mount male end gives you a certified MATEnet interface, and the bare end lets you define your own termination. The 0.2 m to 5 m range covers bench to device routing.
Bare Male Contact Pins to Bare Male Contact Pins
Both ends are left as bare male contact pins, part number 2302451-1, with no plastic housing on either end.Use it when you need to build your own housings on both ends, such as inserting the male pins into custom panel receptacles or non standard MATEnet connectors on both sides.
This gives you the certified Dacar 647-4 cable with factory crimped male pins on both ends, ready for your own housings. The 0.2 m to 5 m range covers custom harness builds and bench test rigs.
Applications
| Application | How It Is Used | What It Enables |
|
Gender adaptation |
Cross a panel mount male pigtail to a female socket. | Bridges two factory harnesses with opposite genders. |
| Bench test rig | Wire MATEnet ECUs to test instruments with male to male or bare ends. | Repeatable gigabit test links instead of hand built cables. |
| Panel mount sensor connection | Clip the male stud into a panel and reach the device. | The connector stays fixed instead of floating on the cable. |
| MATEnet pigtail extension | Extend a factory MATEnet male or female pigtail. | Reaches a relocated ECU or sensor without cutting the factory harness. |
| Custom harness build | Use the bare or pin end to terminate to your own connector. | A certified MATEnet interface with custom termination on one or both ends. |
Closing line: because both ends are TE MATEnet contacts on the same shielded Dacar 647-4 cable, the gigabit link stays impedance matched end to end.
Professional Services
Connector customization: other MATEnet variants quoted on request.
Fast sampling: small batch samples in days, production volumes on a confirmed lead time.
Length customization: 0.2 m to 5 m in stock. Non standard cut lengths built to your drawing.
Quality before dispatch: 100 percent continuity and shielding continuity tested on every assembly before dispatch.
Configuration customization: 5 end options as shown. Other MATEnet gender and coding combinations quoted on request.
OEM and bulk support: zonal ECU developers, ADAS integrators and R and D labs get volume pricing and private label packaging.
Product FAQ
Q1: Which length should I order?
0.2 m to 0.5 m for tight panel jumps or bench use, 1 m to 2 m for dashboard routing, 3 m to 5 m for trunk or across cabin runs. When in doubt, take the next length up.
Q2: Is this a genuine TE MATEnet connector?
Yes. The panel mount A coded male housing is genuine TE MATEnet, part number 2394145-1, black with a round mounting stud. The cable is original LEONI Dacar 647-4 fully shielded gigabit automotive Ethernet.
Q3: What does the panel mount stud do?
The round stud clips into a square hole on a panel or bracket, so the connector stays fixed to the panel instead of hanging loose on the cable. This is used when the connector needs to be mounted through a bulkhead or bracket.
Q4: Can you make custom lengths or end options?
Yes. We support custom lengths from 0.2 m to 5 m and beyond, and can quote other MATEnet gender and coding combinations on request. Send us your connector photos and target length, and we will quote the matching cable.
Hot Tags: te matenet panel to leoni dacar ethernet cable, China te matenet panel to leoni dacar ethernet cable manufacturers, suppliers, factory
