Rosenberger H-MTD To TE MATEnet Adapter Cable

Modern vehicles mix connector systems across the architecture. An ECU may use H-MTD on one port and MATEnet on another, or a sensor may use MATEnet while the zonal ECU uses H-MTD. Directly mating H-MTD to MATEnet is impossible because the two connector systems have different shapes, so a factory made adapter cable is required.This cable bridges the two systems. One end is a Rosenberger H-MTD single port connector, and the other end is a TE MATEnet single port connector. The cable carries the Ethernet signal across the two different connector systems on a shielded line that maintains 100 ohm impedance.

Rosenberger H-MTD single port connector on one end, TE MATEnet single port connector on the other end, factory terminated on GG251 automotive grade cable with optional Dacar 647-4 upgrade. The H-MTD end is available as female E6K10A-1CAZ5-Z or male E6S10A-1BZZ5-Z, and the MATEnet end is available as female 2302510-9 or male 2302461-9. All connectors are water blue Z coded. Available in 5 lengths from 0.1 m to 3 m. Built for zonal architectures that must bridge H-MTD ECUs to MATEnet devices or vice versa.

Whether your ECU uses H-MTD and your sensor uses MATEnet, or your ECU uses MATEnet and your sensor uses H-MTD, this adapter cable crosses the two systems. Pick the gender combination that matches the connectors on both ends.

Product Specifications

Available Configurations

H-MTD Female to MATEnet Female

One end is the Rosenberger H-MTD single port female, E6K10A-1CAZ5-Z, water blue, and the other end is the TE MATEnet single port female, 2302510-9, water blue.

Use it when both sides of the link have male pigtails. The H-MTD female plugs into an H-MTD male sensor or ECU, and the MATEnet female plugs into a MATEnet male device. This is the female to female crossover. The 0.1 m to 3 m length range covers tight panel jumps to across cabin runs.

H-MTD Female to MATEnet Male

One end is the Rosenberger H-MTD single port female, E6K10A-1CAZ5-Z, water blue, and the other end is the TE MATEnet single port male, 2302461-9, water blue.

Use it when the H-MTD side has a male pigtail and the MATEnet side has a female socket. The H-MTD female plugs into the H-MTD male pigtail, and the MATEnet male plugs directly into the MATEnet female socket. The 0.1 m to 3 m range covers tight panel jumps to across cabin runs.

H-MTD Male to MATEnet Female

One end is the Rosenberger H-MTD single port male, E6S10A-1BZZ5-Z, water blue with pink latch, and the other end is the TE MATEnet single port female, 2302510-9, water blue.

Use it when the H-MTD side has a female receptacle and the MATEnet side has a male pigtail. The H-MTD male plugs directly into the H-MTD female socket, and the MATEnet female accepts the MATEnet male pigtail. The 0.1 m to 3 m range covers tight panel jumps to across cabin runs.

H-MTD Male to MATEnet Male

One end is the Rosenberger H-MTD single port male, E6S10A-1BZZ5-Z, water blue with pink latch, and the other end is the TE MATEnet single port male, 2302461-9, water blue.

Use it when both sides of the link have female sockets. The H-MTD male plugs into an H-MTD female receptacle, and the MATEnet male plugs into a MATEnet female socket. This is the male to male crossover. The 0.1 m to 3 m range covers tight panel jumps to across cabin runs.

Applications 

Closing line: because both ends are factory terminated connectors on the same shielded cable, the signal stays impedance matched across the H-MTD to MATEnet crossover.

Professional Services

Cable customization: default GG251. Upgrade to LEONI Dacar 647-4 on request.

Fast sampling: small batch samples in days, production volumes on a confirmed lead time.

Length customization: 0.1 m to 3 m in stock. Non standard cut lengths built to your drawing.

Quality before dispatch: 100 percent continuity and shielding continuity tested on every assembly before dispatch.

Configuration customization: 4 gender combinations as shown. Other H-MTD and MATEnet variants quoted on request.

OEM and bulk support: ADAS integrators, zonal ECU developers and R and D labs get volume pricing and private label packaging.

Product FAQ

Q1: Is this a genuine TE MATEnet connector?

H-MTD is a Rosenberger connector system, and MATEnet is a TE Connectivity connector system. They carry the same Ethernet signal but have different shapes and cannot mate directly. This cable bridges the two systems.

Q2: What is the difference between Config 3 and Config 6?

Yes. We support custom lengths from 0.1 m to 3 m and beyond, and can quote other H-MTD and MATEnet gender and coding combinations on request. Send us your connector photos and target length, and we will quote the matching cable.

Q3: Can you make custom lengths or fan out combinations?

Config 1 is H-MTD female to MATEnet female. Config 2 is H-MTD female to MATEnet male. Config 3 is H-MTD male to MATEnet female. Config 4 is H-MTD male to MATEnet male. Pick the gender combination that matches the connectors on both ends.

Q4: What is the difference between Config 1 and Config 2?

Look at the connector on each end of your existing harness. If your existing connector has pins sticking out, it is male and you need a female end. If your existing connector has sockets, it is female and you need a male end. When in doubt, send us photos of both connectors.