Dual Cavity FAKRA Z Code Coaxial Cable

This automotive camera cable brings two coaxial paths into one straight FAKRA dual cavity housing at each end. Both versions start with a water blue Z Code female connector, reference part number 59Z115-000-Z. The opposite end can use the same female connector or a straight dual cavity male connector, reference part number 59Z116-000-Z.

The choice comes down to the two ports the cable must connect. Use the female to female version where both mating ports require a female cable end. Choose the female to male version where one port requires a female cable end and the other requires a male cable end. Both configurations use RG174 LL coaxial cable and connector housings without waterproof sealing.

Product Specifications

Available Configurations

FAKRA Dual Cavity Female to Female Camera Cable

Connection Structure
59Z115-000-Z straight dual cavity female to 59Z115-000-Z straight dual cavity female.

Unique Difference
The same female connector at both ends gives the harness a matching mating interface on the camera side and the receiving module side.

Suitable Installation
Use this version when the camera and receiving module both have male FAKRA dual cavity ports that mate with the Z Code female cable ends.

FAKRA Dual Cavity Female to Male Camera Cable

Connection Structure
59Z115-000-Z straight dual cavity female to 59Z116-000-Z straight dual cavity male.

Unique Difference
The female end mates with a male dual cavity port, while the male end can connect directly to an existing female dual cavity cable end. 

Suitable Installation
Use this version to extend an existing FAKRA dual cavity camera lead with a female end, or to connect two mating points that require opposite connector genders. Check which side needs the male cable end before routing the harness.

Match the Camera Ports Before Routing the Cable

Two Coaxial Paths in One Housing

Each end groups two coaxial positions in a single housing. In a camera harness layout with a dual cavity FAKRA port, the two positions connect at one mating point. Confirm the cavity assignments against the camera and receiving module drawings before specifying the harness.

Choose the Cable Ends from the Equipment Ports

Both versions use water blue Z Code housings, so the housing color alone does not identify the connector gender. When replacing a harness or preparing an integration sample, compare the mating faces at both equipment ends. This determines whether the assembly needs two female ends or one female and one male end.

Allow Room for a Straight Cable Exit

Both configurations use straight connectors. When planning the route behind a camera module, trim panel or test fixture, allow space for the connector body and the cable leaving the rear of the housing. Choose the cable length based on the installed route between the two ports, including any turns or fixing points along the way.

Use the Assembly in Protected Locations

The connector housings have no waterproof sealing. Typical locations include protected areas inside the vehicle, enclosed camera electronics and indoor test fixtures. For a camera installation exposed to rain or wash water, specify a sealed connector assembly for that location.

OEM Cable Assembly Orders

For a quote or sample, send the required version, cable length and the mating connector references at both ends. If the equipment connector references are unavailable, clear photos of both mating faces can support the initial review. Include the required cavity assignments when each coaxial path must connect to a specific position.

For a drawing based order, specify the finished length measurement points and any label requirements. If your project calls for RTK031 coaxial cable, include that requirement in the inquiry so the cable construction can be reviewed before quoting.

Product FAQ

Can I order this camera cable with two female ends ?
Yes. Version 1 uses a straight FAKRA dual cavity Z Code female connector at each end. The female connector reference is 59Z115-000-Z.

Which version uses the 59Z116-000-Z male connector ?
Version 2 pairs a 59Z115-000-Z female connector with a 59Z116-000-Z male connector. Both ends are straight dual cavity FAKRA Z Code.

Are these original Rosenberger connectors ?
The assembly uses Rosenberger style compatible connectors. The reference part numbers identify the connector styles used for selection.

Does the cable temperature range apply to the complete assembly ?
The listed range of −40°C to 105°C applies to the RG174 LL coaxial cable. For a complete assembly temperature requirement, include the operating conditions in your inquiry.

How do I confirm which cavity connects to which at the opposite end ?
Send the cavity numbering and required channel mapping with your drawing or inquiry. The mapping can then be reviewed against the proposed assembly before sample production.