Product Specifications
| Item | Specification |
| Characteristic Impedance | 90Ω |
| Connector Series | GT17H |
| Cable Outer Diameter | 4.6mm |
| Axial Pull Strength | ≥110N |
| Connector Brand | Hirose |
| Frequency Range | 480MHz |
| Cable Length | 2000±20mm |
| Insulation Resistance | 100MΩ Min |
| Insertion and Extraction Durability | ≥25 cycles |
| Drawing Number | PCM-ZC-0246 |
| P2 Housing | GT17H-4S-HU |
| P1 Housing | GT17HS-4S-HU |
| Withstand Voltage | 500V RMS Min |
| Connector Configuration | GT17H to GT17H |
| Insulation Case | GT17H-4S-2C(A) |
| Operating Temperature | -40°C to 105°C |
| Single Wall Casing | OD 5.0mm, Black, Length 20mm |
| Cable Construction | USB2.0 (26#/1P+AM)+24#/2C+AB OD4.6MM |
Connector Configuration and Cable Performance

Distinct Housing Selection at Both Ends
The two connection ends use separate Hirose housing configurations. P1 is equipped with GT17HS-4S-HU, while P2 uses GT17H-4S-HU. Both ends incorporate the GT17H-4S-2C(A) insulation case. This arrangement follows the connector specifications shown in the engineering drawing and preserves the designated mechanical interface at each termination.
A Key Interface Compatibility
Both connector ends feature the brown GT17H-4S-2C(A) A Key insulation case. This keying configuration is important when integrating the cable into equipment designed around the corresponding Hirose GT17H interface. Selecting the specified insulation case helps maintain correct mating compatibility and prevents confusion with alternative key configurations.


Defined Shielded Cable Construction
The cable follows the drawing designation USB2.0 (26#/1P+AM)+24#/2C+AB OD4.6MM. Its construction combines the specified signal conductors, additional cores and overall shielding within a 4.6mm outer diameter. This configuration is intended for USB 2.0 signal interconnection, with a specified characteristic impedance of 90Ω and frequency range of 480MHz.
Mechanical and Electrical Requirements
Beyond the connector arrangement, this assembly is manufactured against defined electrical and mechanical requirements. The drawing specifies insulation resistance of at least 100MΩ, withstand voltage of 500V RMS minimum, insertion and extraction durability of 25 cycles or more, and axial pull strength of at least 110N. Its operating temperature range extends from -40°C to 105°C.

Equipment Applications and Customization
GT17H Equipment Interconnection
This dual ended assembly is intended for electronic equipment equipped with compatible Hirose GT17H interfaces at both connection points. Its specified connector keying and different housing configurations make it suitable for dedicated equipment wiring where the mating structure is predetermined by the system design.
Automotive and Embedded Electronics
The Hirose GT17H series is designed for shielded high speed signal transmission and automotive connector applications. This cable assembly can be considered for automotive electronic modules, embedded control systems and other equipment requiring a matched GT17H connection. Final compatibility should be assessed against the equipment interface and electrical requirements.
Drawing Based Production Customization
Premier Cable provides cable assembly development according to customer drawings and technical requirements. Connector models, housing arrangements, conductor assignments, cable construction and finished length can be evaluated during project development. This allows the assembly structure to be adapted to different equipment layouts while retaining the required interface specifications.
Product Drawing

Product FAQ
What is the finished cable length and outer diameter ?
The specified finished length is 2000±20mm, and the cable has a nominal outer diameter of 4.6mm.
Are both connectors equipped with the same key configuration ?
Yes. Both ends use the brown GT17H-4S-2C(A) A Key insulation case, providing the specified mating key configuration.
What connector configurations are used at the two ends ?
P1 uses the GT17HS-4S-HU housing, while P2 uses the GT17H-4S-HU housing. Both ends incorporate GT17H-4S-2C(A) insulation cases.
What shielding and impedance requirements does the cable meet ?
The cable follows the specified USB 2.0 shielded construction and has a characteristic impedance of 90Ω with a frequency range of 480MHz.
What mechanical and environmental requirements are specified ?
It specifies at least 25 insertion and extraction cycles, axial pull strength of at least 110N and an operating temperature range of -40°C to 105°C.
Hot Tags: hirose gt17h automotive usb 2.0 cable, China hirose gt17h automotive usb 2.0 cable manufacturers, suppliers, factory

