TE MATEnet With Panel Clip To LEONI Dacar Ethernet Cable

TE MATEnet Z coded single port male connector, part number 2394145-9, water blue, factory fitted with a panel mounting clip for direct panel snap in installation, on original LEONI Dacar 647-4 fully shielded gigabit automotive Ethernet cable. The clipped male end snaps into a 7 by 12 millimeter hole on 0.7 to 2 millimeter panel thickness. The other end is offered as MATEnet female, another clipped male, bare female core without housing, bare wire, or bare male core on both ends. Available in 9 lengths from 0.2 m to 5 m. Built for gigabit Ethernet links where the male end must snap directly into a body panel or bracket.

When a MATEnet male connector needs to mount directly into a body panel or bracket without a separate screw, the clipped version with an integrated panel retaining clip is used. The clip, part number 151-02898, snaps into a 7 by 12 millimeter hole on panel thickness from 0.7 to 2 millimeters. This eliminates a separate fastener and speeds up assembly on the production line.This harness starts from that clipped MATEnet Z coded male, 2394145-9, and covers the full range to female, to another clipped male, to bare female core, to bare wire, or to bare male core on both ends. The cable is original LEONI Dacar 647-4, a gigabit shielded line built to hold 100 ohm differential impedance end to end.

Whether you are snapping the clipped male into a body panel and running to a female device, bridging two clipped male ends, building a custom harness from bare core, or starting from bare wire, this harness has the configuration you need. Pick the option that matches your build.

Product Specifications

Available Configurations

Clipped Male to MATEnet Female

The clipped MATEnet Z coded male, 2394145-9, snaps into a body panel or bracket, and the other end is the MATEnet single port female, 2302510-9, water blue.

Use it when the male end mounts directly into a panel and the female end plugs into a MATEnet male pigtail on the device side. The clipped male holds itself in the panel hole without a screw. The female end accepts a standard MATEnet male pigtail. The 0.2 m to 5 m range covers panel to sensor routing.

Clipped Male to Clipped Male

Both ends are the clipped MATEnet Z coded male, part number 2394145-9, water blue.Use it when you need to bridge two MATEnet female sockets, each mounted in its own panel or bracket.

Both clipped male ends snap into their respective panel holes. The male to male gender reaches across the gap between two female receptacles. The 0.2 m to 5 m range covers panel to panel routing.

Clipped Male to Bare Female Core

The clipped MATEnet Z coded male, 2394145-9, snaps into a body panel, and the other end is the MATEnet female contact core without the outer blue plastic housing.

Use it when the female side needs to mount into your own custom adapter block, test fixture or customer specified housing, instead of using the factory blue plastic shell. The bare female contact accepts a MATEnet male plug directly. The 0.2 m to 5 m lengths cover custom harness builds and bench rigs.

Clipped Male to Bare Wire

The clipped MATEnet Z coded male, 2394145-9, snaps into a body panel, and the other end is bare wire with no connector terminated.

Use it when you want to crimp your own connector on the other end, or when you are building a custom harness that terminates to a PCB, splice pack or customer specified connector. The clipped male end is pre terminated and tested, and the bare wire end is ready for your own crimp. The 0.2 m to 5 m lengths cover custom harness builds.

Bare Male Core to Bare Male Core

Both ends are the MATEnet Z coded male contact core, part number 2302451-1, without the outer plastic housing or clip.

Use it for fully custom harness builds where both ends need to mount into your own panels, adapter blocks or test fixtures, without the factory plastic shells. Both bare male cores plug directly into MATEnet female sockets. The 0.2 m to 5 m lengths cover bench rigs and custom harness builds.

Applications 

Closing line: because the clipped male end is factory terminated on the same shielded Dacar 647-4 cable, the gigabit link stays impedance matched from the panel mounted male to the device end.

Professional Services

Panel clip customization: clip 151-02898 standard. Other clip styles on request.

Fast sampling: small batch samples in days, production volumes on a confirmed lead time.

Length customization: 0.2 m to 5 m in stock. Non standard cut lengths built to your drawing.

Configuration customization: 5 options as shown. Other MATEnet termination options quoted on request.

Quality before dispatch: 100 percent continuity and shielding continuity tested on the terminated ends before dispatch.

OEM and bulk support: zonal ECU developers, ADAS integrators and harness builders get volume pricing and private label packaging.

Product FAQ

Q1: What is the panel clip for?

The panel clip, part number 151-02898, lets the clipped male connector snap directly into a 7 by 12 millimeter hole on a 0.7 to 2 millimeter panel. No separate screw or fastener needed.

Q2: Can you make custom lengths or termination options?

Yes. We support custom lengths from 0.2 m to 5 m and beyond, and can quote other MATEnet termination options on request. Send us your drawing and target length, and we will quote the matching harness.

Q3: What is Config 3 used for?

Config 3 supplies the female contact core without the blue plastic housing. This is for custom harness builders who want to mount the contact into their own adapter block or test fixture, instead of using the factory plastic shell.

Q4: What is the difference between the five configurations?

Config 1 is clipped male to female. Config 2 is clipped male to clipped male. Config 3 is clipped male to bare female core without housing. Config 4 is clipped male to bare wire. Config 5 is bare male core on both ends without housing.