Product Specifications
| Item | Specification |
| Characteristic Impedance | 90Ω |
| Cable Outer Diameter | 4.6mm |
| Axial Pull Strength | ≥110N |
| Number of Contacts | 4 Pins |
| Frequency Range | 480MHz |
| Cable Length | 600±20mm |
| Insulation Resistance | 100MΩ Min |
| P1 Connector | USB2.0 A/F |
| Insertion and Extraction Durability | ≥25 Cycles |
| Drawing Number | PCM-ZC-0254 |
| P2 Connector | GT17H-4S-2C |
| Withstand Voltage | 500VRMS Min |
| P2 Connector Shell | GT17HS-4S-HU |
| Insulation Material | Transparent PE |
| Operating Temperature | -40°C to 105°C |
| Connector Brand | Hirose Original |
| Outer Jacket | 45P PVC Compound, Black |
| Cable Construction | USB2.0 (26#/1P+AM)+24#/2C+AB |
| Single Wall Casing | Black, OD 5.0mm, Length 20mm |
| Product Type | USB2.0 Type A Female to Hirose GT17H Cable Assembly |
Product Features
USB Type A Female Socket Interface
The P1 end is designed with a USB2.0 Type A Female receptacle, providing a socket connection rather than a protruding USB plug. This arrangement is suitable for equipment designs where the USB connection point needs to accept an external Type A Male connector. The molded black connector housing incorporates the USB identification symbol and a structured cable entry. This interface configuration allows equipment designers to position the USB socket through a dedicated cable assembly instead of integrating the USB receptacle directly into the main circuit board.
Hirose GT17H Connector and Housing Combination
The P2 connection uses the original Hirose GT17H-4S-2C connector together with the GT17HS-4S-HU shell. These two specified components form the dedicated 4 pin connection end of the assembly. The connector housing and shell provide the mechanical interface required by the GT17H configuration, while the original part number identification helps maintain component traceability during purchasing and production. This is particularly useful for equipment projects that specify a particular connector series and require consistent cable replacement or assembly sourcing.
Dedicated Four Conductor Wiring Arrangement
The internal wiring follows a defined four conductor arrangement between the USB Type A Female receptacle and the GT17H connector. The red conductor carries VCC, the white conductor carries D-, the green conductor carries D+, and the black conductor carries GND. Each conductor follows the corresponding Pin 1 through Pin 4 assignment at both ends. The connector shells are also connected to GND as indicated in the engineering drawing. This arrangement provides a clear wiring reference for continuity testing, assembly inspection, and production verification.
Defined Cable and Termination Construction
The cable assembly uses a specified USB2.0 (26#/1P+AM)+24#/2C+AB construction with a 4.6mm outer diameter. The material configuration includes transparent PE material and black 45P PVC compound. At the GT17H cable termination, a black single wall casing with a 5.0mm outer diameter and 20mm length is specified. The finished cable length is controlled at 600±20mm, providing a defined physical arrangement for equipment routing and assembly. These details establish clear manufacturing references for cable preparation and dimensional inspection.
Applications and Customization
USB Socket Integration
The USB Type A Female receptacle provides an accessible connection point for equipment that requires an external USB plug connection. It is suitable for electronic control units, embedded equipment, and other systems designed around a separate USB socket connected through an internal cable assembly.
Dedicated GT17H Equipment Connection
The Hirose GT17H-4S-2C connector and GT17HS-4S-HU shell provide the specified cable side interface. This configuration is suitable for equipment designs that use the GT17H connector series and require a defined 4 pin connection arrangement.
OEM Cable Assembly Development
Premier Cable supports customized cable assembly development based on engineering drawings and application requirements. Available evaluation items include cable length, connector configuration, wire assignment, cable materials, protective casing, and assembly dimensions. Drawing review, prototype development, and production arrangements can be coordinated according to project requirements.
Product Drawing
Product FAQ
What is the cable length and how is the assembly configured ?
The finished cable length is 600±20mm, with a cable outer diameter of 4.6mm. The assembly also includes a black single wall casing with a 5.0mm outer diameter and a length of 20mm at the cable termination.
How does the cable maintain the correct signal correspondence ?
The four conductors are assigned by color and pin number. Red corresponds to VCC, white to D-, green to D+, and black to GND. Both connector shells are connected to GND according to the engineering drawing.
What makes the PCM-ZC-0254 connector configuration different ?
The PCM-ZC-0254 uses a USB2.0 Type A Female receptacle at P1 and an original Hirose GT17H-4S-2C connector at P2. The GT17HS-4S-HU shell completes the specified 4 pin connector assembly for equipment integration.
What electrical and mechanical requirements does this assembly meet ?
The drawing specifies 90Ω characteristic impedance, 100MΩ Min insulation resistance, 480MHz frequency range, and 500VRMS Min withstand voltage. Mechanical requirements include ≥25 insertion and extraction cycles and ≥110N axial pull strength.
Can Premier Cable manufacture this assembly to different project requirements ?
Yes. Premier Cable can evaluate alternative cable lengths, connector arrangements, wiring definitions, cable materials, and protective structures based on customer drawings. Prototype development and production planning can also be arranged according to project requirements.
Hot Tags: hirose gt17h-4s-2c usb female cable, China hirose gt17h-4s-2c usb female cable manufacturers, suppliers, factory
